In computer networking, the link layer is the lowest layer in the Internet Protocol Suite (commonly known as "TCP/IP"), the networking architecture of the Internet (RFC 1122, RFC 1123). It is the group of methods or protocols that only operate on a host's link. The link is the physical and logical network component used to interconnect hosts or nodes in the network and a link protocol is a suite of methods and standards that operate only between adjacent network nodes of a Local area network segment or a wide area network connection.
Despite the different semantics of layering in TCP/IP and OSI, the link layer is often described as a combination of the data link layer (layer 2) and the physical layer (layer 1) in the Open Systems Interconnection (OSI) protocol stack. However, TCP/IP's layers are descriptions of operating scopes (application, host-to-host, network, link) and not detailed prescriptions of operating procedures, data semantics, or networking technologies.
RFC 1122 exemplifies that local area network protocols such as Ethernet and IEEE 802, and framing protocols such as Point-to-Point Protocol (PPP) belong to the link layer.
Definition in standards and text books
LAN standards such as Ethernet and IEEE 802 specifications use terminology from the seven-layer OSI model rather than the TCP/IP reference model. The TCP/IP model in general does not consider physical specifications, rather it assumes a working network infrastructure that can deliver media level frames on the link. Therefore RFC 1122 and RFC 1123, the definition of the TCP/IP model, do not discuss hardware issues and physical data transmission and set no standards for those aspects, other than broadly including them as link-layer components. Some textbook authors[1][2] have supported the interpretation that physical data transmission aspects are part of the link layer. That position will be held in the rest of this article. Others[3][4] assumed that physical data transmission standards are not considered as communication protocols, and are not part of the TCP/IP model. These authors assume a hardware layer or physical layer below the link layer, and several of them adopt the OSI term data link layer instead of link layer in a modified description of layering. In the predecessor to the TCP/IP model, the Arpanet Reference Model (RFC 908, 1982), aspects of the link layer are referred to by several poorly defined terms, such as network-access layer, network-access protocol, as well as network layer, while the next higher layer is called internetwork layer. In some modern text books, network-interface layer, host-to-network layer and network-access layer occur as synonyms either to the link layer or the data link layer, often including the physical layer.
Link-layer protocols
The core protocols specified by the Internet Engineering Task Force to be placed into this layer are the Address Resolution Protocol (ARP), its cousin, the Reverse Address Resolution Protocol (RARP), and the Neighbor Discovery Protocol (NDP), which is a facility delivering similar functionality as ARP for IPv6. Since the advent of IPv6, Open Shortest Path First (OSPF) can be considered to operate on the link level as well, although the IPv4 version of the protocol was considered at the Internet layer.
IS-IS (RFC 1142) is another link-state routing protocol that fits into this layer when considering TCP/IP model, however it was developed within the OSI reference stack (where it is a layer-3 protocol). It is not an Internet standard.
The link layer also contains all hardware specific interface methods, such as Ethernet and other IEEE 802 encapsulation schemes (see References).
Relation to OSI model
The link layer of the TCP/IP model is often compared directly with the combination of the data link layer and the physical layer in the Open Systems Interconnection (OSI) protocol stack. Although they are congruent to some degree in technical coverage of protocols, they are not identical. The link layer in TCP/IP is still wider in scope and in principle a different concept and terminology of classification. This may be observed when certain protocols, such as the Address Resolution Protocol (ARP), which is confined to the link layer in the TCP/IP model, is often said to fit between OSI's data link layer and the network layer. In general, direct or strict comparisons should be avoided, because the layering in TCP/IP is not a principal design criterion and in general is considered to be "harmful" (RFC 3439).
Another term sometimes encountered, "network-access layer", tries to suggest the closeness of this layer to the physical network. However, this use is misleading and non-standard, since the link layer implies functions that are wider in scope than just network access. Important link-layer protocols are used to probe the topology of the local network, discover routers and neighboring hosts, i.e. functions that go well beyond network access.
Examples of functions supported
The link layer includes the following functionality:
- Logical link-local networking methods
- Encapsulation of IP packets into frames
- Frame synchronization
- Error detection with removal of erroneous packets (Used in LANs and point-to-point fiber optical cables)
- Logical link control (LLC) sublayer: (Used in modem protocols and wireless protocols)
- Node-to-node error detection and automatic repeat request of erroneous packets
- Node-to-node flow control
- Forward error correction (however much more common at the physical layer)
- Media access control (MAC) sublayer:
- Help protocols not encapsulated in IP packets:
- Physical networking aspects: (It is disputable if and to which extent these are included)
- Bit-by-bit or symbol-by-symbol delivery
- Net bit rate
- Digital modulation
- Line coding
- Carrier sense and collision detection utilized by some level 2 multiple-access protocols
- Circuit switching, establishing circuit switched connections
- Multiplexing
- Forward error correction codes
- Serial or parallel communication
- Bit synchronization
- Start-stop signalling and flow control in asynchronous serial communication
- Signal strength (voltage and power levels), impedance
- Forward error correction, bit-interleaving and other channel coding
- Equalization filtering, training sequences, pulse shaping and other signal processing of physical signals
- Mechanical specification of electrical connectors and cables, for example maximum cable length
- Electrical specification of transmission line signal level and impedance
- Radio interface, including electromagnetic spectrum frequency allocation and specification of signal strength, analog bandwidth, etc.
- Specifications for IR over optical fiber or a wireless IR communication link
RFC references
- RFC 1122, "Requirements for Internet Hosts -- Communication layers," IETF, R. Braden (Editor), October 1989
- RFC 1123, "Requirements for Internet Hosts -- Application and Support," IETF, R. Braden (Editor), October 1989
- RFC 893, "Trailer Encapsulations," S. Leffler and M. Karels, April 1984
- RFC 826, "An Ethernet Address Resolution Protocol," D. Plummer, November 1982
- RFC 894, "A Standard for the Transmission of IP Datagrams over Ethernet Networks," C. Hornig, April 1984
- RFC 1042, "A Standard for the Transmission of IP Datagrams over IEEE 802 Networks," J. Postel and J. Reynolds, February 1988
- RFC 2740, "OSPF for IPv6", R. Coltun, et al., December 1999
See also
Other layers defined in the OSI model of networking that relate to the link layer:
References
- ^ James F. Kurose, Keith W. Ross, Computer Networking: A Top-Down Approach, 2007, ISBN 0-321-49770-8
- ^ Mark Dye, Mark A. Dye, Wendell, Network Fundamentals: CCNA Exploration Companion Guide, 2007, ISBN 1-58713-208-7
- ^ Douglas E. Comer, Internetworking with TCP/IP: Principles, Protocols and Architecture, Pearson Prentice Hall 2005, ISBN 0-13-187671-6
- ^ Charles M. Kozierok, "The TCP/IP Guide", No Starch Press 2005
External links
